DIY

Storage Building

Roof – Radiant Barrier

Wall – Masonry R-3.7 and R-7.0

Wall – 2” x 4” R-6.6 (No Fiberglass)

Wall – 2” x 4” R-14 Total Assembly (R-3.9 and a Vapor/Moisture Barrier for the Reflectix®)

Note: Installation instructions and illustrated drawings are recommendations only, while proper local construction methods are the responsibility of the installer.

Reflectix® products provide a wide range of Insulation and Radiant Barrier options for the Do-It-Yourselfer. Depending on the structure of your building and the level of benefit required, Reflectix has an “easy to install” option to consider.

Recommended Products

Double Reflective Insulation

Reflective/Bubble/Bubble/Reflective – Roll

  • BP24025 (24” x 25’)
  • BP48025 (48” x 25’)

Staple Tab, Reflective/Bubble/Bubble/Reflective – Roll

  • ST16025 (16” x 25’)
  • ST24025 (24” x 25’)
Radiant Barrier

Radiant Barrier, Reflective/Woven Fabric/Reflective – Roll (Heavy Duty)

  • RB4812550 (48” x 125’)

Note: Click here for information on our larger rolls which are available by Special Order at the Contractor or Customer Service Desks.

Benefits

  • Wide range of installation options
  • Installs quickly and easily
  • Product does not contain fibers or dust that require respirators or protective garments
  • Non-toxic / non-carcinogenic
  • Reduces the level of interior temperature fluctuations

Installation Instructions

Standard Edge 72 RGB RB4812550 Top of Roll 72 RGB
Double Reflective Insulation or Radiant Barrier

Installation Instruction pdf: DIY Storage Building Revised 012021

1. Roof

  • Refer to the Reflectix® Webpage “DIY Attic”.
Standard Edge 72 RGB
Double Reflective Insulation

Installation Instruction pdf: DIY Storage Building Revised 012021

2. Wall – Masonry R-3.7 and R-7.0

  • Refer to the Reflectix® Webpage “DIY Wall – Masonry”.

3. Wall – 2”x 4” R-6.6 (no fiberglass)

  • Determine if studs are 16” or 24” on center (This will determine whether Reflectix® 16” or 24” product is utilized).
  • Place one corner edge of the Reflectix® in an upper corner of the stud cavity. At a point that splits the stud cavity; staple the product to the side of the stud (creating a 3/4” tab on the product).
  • Proceed “down”, stapling to the side of the stud every 2″- 3”.
  • Repeat procedure on opposite stud.
  • The Goal: Create two approximately equal continuous 1 3/4” air spaces on each side of the Reflectix® Insulation.
  • This application also provides a vapor/moisture barrier.
  • Finish wall interior with a panel or sheathing (Product is not specified as an interior wall covering).

4. Wall – 2”x 4” R-14 Total Assembly

(R-3.9 and a Vapor Moisture Barrier for the Reflectix®)

  • Refer to the Reflectix® Webpage “DIY Wall – Exterior – 2”x 4””.

Important

Review These Important Safety Guidelines Prior to Installation:

  • ALWAYS check local building codes before installing Reflectix®.
  • ALWAYS check the area you are insulating and make any needed repairs. Any worn wiring should be replaced before you begin installing Reflectix®.
  • ALWAYS make sure work areas are well ventilated and well lighted.
  • ALWAYS use eye protection when operating a staple gun.
  • ALWAYS use caution and common sense when using a staple gun. Be aware of electrical wiring locations. Stapling into a wire can cause severe shock or death. NEVER staple into electrical wiring.
  • ALWAYS be careful when working with large pieces of Reflectix® on windy days.
  • When installing Reflectix® on bright sunny days, it is best to wear sun glasses.
  • Do not work in areas such as attics when temperatures are too hot.
  • Please Note: The intention of these Installation Instructions and 3-D renderings are for the sole purpose of illustrating the correct location and relative position of the Reflectix® products in specific building assemblies. The correct construction methods and techniques are the responsibility of the installer or contractor. The methods outlined are recommendations on location of the Reflectix® products as a guideline. There are no claims on the part of Reflectix, Inc. that these building assemblies are finite standards or meet building code requirements (as they can vary by region).

Testing and Certification

Reflectix® products are thoroughly tested at either nationally approved, independent laboratories or leading universities. Tests are performed to current American Society of Testing and Materials (ASTM) standards when a standard exists. To obtain a copy of our Product Testing Specifications, please refer to the “Additional Resources” tab. The documents are also available by e-mail at customerservice@reflectixinc.com or call (800) 879-3645.

Photos

Pictured: 1. Double Reflective Insulation, 2. Double Reflective Insulation with Staple Tab, 3. Tools for Installation