Product: Reflective Both Sides

Post Frame Building – Wall – New

Inside the Girts
Metal Interior: R-6.3 
Open Interior: R-5.3 

Outside the Girts
Metal Interior: R-5.5 
Open Interior: R-4.7 

Note: Installation instructions and illustrated drawings are recommendations only, while proper local construction methods are the responsibility of the installer.

Reflectix® Insulation products are a group of technologically advanced materials. They are ideal for new construction or retrofit applications in commercial, industrial, metal and post/frame buildings, along with many other DIY applications. When you think of insulation, you should think of Reflectix®. Our products are recognized for their thermal performance, easy installation, versatility and price.

Recommended Products

Double Reflective Insulation

Staple Tab, Reflective/Bubble/Bubble/Reflective – Roll

  • ST48100 (48” x 100’)

Benefits

  • Easy to handle and install
  • Convenient roll sizes
  • Class A / Class 1 Fire Rating
  • Inhibits dew point condensation
  • Vapor retarder (0.02 perms)
  • Does not compress, collapse or disintegrate
  • Non-toxic / non-carcinogenic

Installation Instructions

Installation Instruction pdf: PFB2 Wall New Revised 012021

There are 2 Installation Options

1. Product Inside the Girts

  • Attach the product using 5/16” staples at approximately 4” intervals.
  • Staple the Reflectix® Reflective/Bubble/Bubble/Reflective, Staple Tab product to the outside of the top girt.
  • Staple the product to the inside of the remaining girts.
  • Tape the seams with a Reflectix® Foil Tape (goal is an air-tight, snug seam seal).
  • For interior covering, attach 1”x 2” furring strips perpendicular to the girts through the insulation.
  • Attach interior panel to the furring strips.
  • This will provide a 1” (nominal) air space between the interior panel and the insulation and a 1 1/2” air space between the insulation and the outside panel.

2. Product Outside the Girts

  • Attach the product using 5/16” staples at approximately 4” intervals.
  • Staple the Reflectix® Reflective/Bubble/Bubble/Reflective, Staple Tab product to the outside of the top girt.
  • Staple the product to the outside of the remaining girts. Insure there is a drape of at least 3/4” (towards the interior of the building) at the center of each cavity.
  • Tape the seams with a Reflectix® Foil Tape (goal is an air-tight, snug seam seal).
  • Attach outside panel.
  • Attach interior panel to the inside of the girts (if specified).

Calculation Disclaimer: All values are calculated based on the “ASHRAE Handbook of Fundamentals”.

Important

Review These Important Safety Guidelines Prior to Installation:

  • ALWAYS check local building codes before installing Reflectix®.
  • ALWAYS check the area you are insulating and make any needed repairs. Any worn wiring should be replaced before you begin installing Reflectix®.
  • ALWAYS make sure work areas are well ventilated and well lighted.
  • ALWAYS use eye protection when operating a staple gun.
  • ALWAYS use caution and common sense when using a staple gun. Be aware of electrical wiring locations. Stapling into a wire can cause severe shock or death. NEVER staple into electrical wiring.
  • ALWAYS be careful when working with large pieces of Reflectix® on windy days.
  • When installing Reflectix® on bright sunny days, it is best to wear sun glasses.
  • Do not work in areas such as attics when temperatures are too hot.
  • Please Note: The intention of these Installation Instructions and 3-D renderings are for the sole purpose of illustrating the correct location and relative position of the Reflectix® products in specific building assemblies. The correct construction methods and techniques are the responsibility of the installer or contractor. The methods outlined are recommendations on location of the Reflectix® products as a guideline. There are no claims on the part of Reflectix, Inc. that these building assemblies are finite standards or meet building code requirements (as they can vary by region).

Testing and Certification

Reflectix® products are thoroughly tested at either nationally approved, independent laboratories or leading universities. Tests are performed to current American Society of Testing and Materials (ASTM) standards when a standard exists. To obtain a copy of our Product Testing Specifications, please refer to the “Additional Resources” tab. The documents are also available by e-mail at customerservice@reflectixinc.com or call (800) 879-3645.

Photos

Pictured: 1. Double Reflective Insulation, 2. Double Reflective Insulation with Staple Tab