DIY

Duct Insulation R-4.2

R-4.2

Note: Installation instructions and illustrated drawings are recommendations only, while proper local construction methods are the responsibility of the installer.

Utilizing Reflectix® to enhance the efficiency of your existing duct system, is one of the “easiest to install” products you can select. There are no fibers or dust contained in the product, thus no need for respirators or protective garments.

Recommended Products

Double Reflective Insulation

Reflective/Bubble/Bubble/Reflective – Roll

  • BP48025 (48” x 25’)

Duct Insulation, Reflective/Bubble/Bubble/Reflective – Roll

  • DW12025 (12” x 25’)

Note: Click here for information on our larger rolls which are available by Special Order at the Contractor or Customer Service Desks.

Benefits

  • R-4.2
  • Easy to handle and install
  • Non-toxic / non-carcinogenic
  • Lightweight and clean
  • Not affected by moisture or humidity
  • Resists growth of fungi, mold and mildew
  • When installed properly, aides in the reduction of duct leakage

Installation Instructions

Installation Instruction pdf: DIY Duct Insulation R-4.2 Revised 012021

There are 2 Installation Options

 1. Standard Wrap (Reflective/Bubble/Bubble/Reflective – Roll product)

  • Make sure all metal joints, seams and penetrations are sealed.
  • Verify circumference of the duct.
  • Cut the Reflectix® product to this length plus 1”.
  • Wrap the product around the duct and securely tape the linear and circumference seams (overlapping 1″- 2″) with a UL 181 Tape (goal is an air-tight, snug seam seal). Do not leave any exposed duct or space where air can enter between the duct and the Reflectix®.

2. Spiral Wrap Directly Against Duct (Reflective/Bubble/Bubble/Reflective, Duct Insulation – Roll product)

  • Make sure all metal joints, seams and penetrations are sealed.
  • Spiral wrap Reflectix® around the duct, overlapping 2” as you proceed.
  • If necessary, trim width of product to accommodate bends or diameter changes in the duct.
  • Securely tape seams with a UL 181 Tape (goal is an air-tight, snug seam seal).
  • Do not leave any exposed duct or space where air can enter between the duct and the Reflectix

Installation Video

Important

Review These Important Safety Guidelines Prior to Installation:

  • ALWAYS check local building codes before installing Reflectix®.
  • ALWAYS check the area you are insulating and make any needed repairs. Any worn wiring should be replaced before you begin installing Reflectix®.
  • ALWAYS make sure work areas are well ventilated and well lighted.
  • ALWAYS use eye protection when operating a staple gun.
  • ALWAYS use caution and common sense when using a staple gun. Be aware of electrical wiring locations. Stapling into a wire can cause severe shock or death. NEVER staple into electrical wiring.
  • ALWAYS be careful when working with large pieces of Reflectix® on windy days.
  • When installing Reflectix® on bright sunny days, it is best to wear sun glasses.
  • Do not work in areas such as attics when temperatures are too hot.
  • Please Note: The intention of these Installation Instructions and 3-D renderings are for the sole purpose of illustrating the correct location and relative position of the Reflectix® products in specific building assemblies. The correct construction methods and techniques are the responsibility of the installer or contractor. The methods outlined are recommendations on location of the Reflectix® products as a guideline. There are no claims on the part of Reflectix, Inc. that these building assemblies are finite standards or meet building code requirements (as they can vary by region).

Testing and Certification

Reflectix® products are thoroughly tested at either nationally approved, independent laboratories or leading universities. Tests are performed to current American Society of Testing and Materials (ASTM) standards when a standard exists. To obtain a copy of our Product Testing Specifications, please refer to the “Additional Resources” tab. The documents are also available by e-mail at customerservice@reflectixinc.com or call (800) 879-3645.

Photos

Pictured: 1. Double Reflective Insulation, 2. 12″ x 25′ Duct Insulation, 3. Taping the Seam with a UL 181 Tape

Damon UL181 Taping Duct 72 RGB